micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 24

Страница: 24 / 84

Overview of MT-3405D Console Func tions

The MT-3405D features three large, easy-to-read liquid crystal displays and a lighted panel for night use. The right-hand displays

always show the application rates and the left-hand display shows data selected by the rotary switch and the controller selection as

indicated by the yellow lights above the rotary switch.

Use the On/Off Switch at upper left to turn console on or off.

VOLUME (1) (2) (3):

Displays total gallons (liters) or lbs. (kg)

of NH3 applied. May be reset. (Note: VOLUME and AREA

counters work in pairs, if VOLUME counter 1 is reset, it also

resets AREA counter 1).

VOLUME/MINUTE:

Displays total

gallons (liters) of liquid applied

per minute, or lbs. (kg) NH3 per

minute.

TANK:

Displays gallons

(liters) of liquid remaining or

lbs. (kg) of NH3 remaining.

RATE:

Displays application

rate GPA(LPH), or lbs. N/acre

(kg of N/hectare).

MIN FLOW:

Used in the calibration mode to enter the

minimum flow rate (GPM/LPM) of the spray boom.

ADJUST RATE:

Used in calibration mode to enter an

amount of change for on-the-go adjustments to the target

rate (GPA/LPH), or lbs/acre (kg/hectare) N.

TARGET RATE:

Used in calibration mode to enter the target

application rate (GPA/LPH) or lbs/acre (kg/hectare) N. Can

also be used to disable either Ch1 or Ch2 (set target rate = 0).

AREA (1) (2) (3):

Keeps a running count of the total acres

(hectares) worked. May be reset. (Note: VOLUME and AREA

counters work in pairs, if AREA counter 1 is reset, it also resets

VOLUME counter 1).

DISTANCE:

Displays distance

traveled in feet (meters). May be

reset.

AREA/HOUR:

Displays

current work rate in acres

per hour (hectares per

hour).

WIDTH CAL:

Used in calibration mode to

enter the working width of your sprayer

booms or other equipment.

SPEED:

Displays ground

speed in miles per hour

(kilometers per hour).

SPEED CAL:

Used in calibration mode to enter the speed

calibration number in inches (cm) per pulse.

INLINE/BYPASS:

For establishing servo polarity. (If servo is

in the main spray line, select “Inline”. If servo is installed in a

return line, select “Bypass”.)

TEST SPEED:

Used in calibration mode to enter a test speed

in miles per hour (kilometers per hour).

CONT SEL:

Key

used to select

which data

is displayed.

Controller 1 or 2.

CAL:

This key is

used to enter &

exit the calibration

mode.

ON/OFF:

Press

up or down

to turn the

console ON

or OFF. Left-

hand display

shows hours

of operation

for 2 seconds,

then software

version for 2

seconds, then

begins normal

operation.

Key Functions

PROGRAM KEYS:

Used to increment and

decrement the different

calibration values.

• RESET when not in

CAL, clears the selected

counter when held for

two sec onds.

• When in CAL, the “+”

key increases and the

“-” decreases the value

displayed.

These buttons are used to adjust the

Application Rate (for either manual or

automatic operation) as follows:

MAN:

These buttons manually adjust

the servo valve, which changes the

application rate.

AUTO:

These buttons either raise or

lower the target application rate by

the amount specified by “Adjust Rate”

setting, in Calibration. The controller

then automatically controls the servo

valve to lock on to this new rate.

FLOW CAL:

Used in calibration mode to

enter the calibration value assigned to

your flowmeter (see flowmeter tag.)

WARNING LIGHTS: Indicates over or

under application of plus or minus

10% from the Target Rate or if the

tank is low. Also lit when in CAL.

Calibration Positions

Key Functions

CONT

SEL

CAL

RESET

Ch2

Ch1

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды