micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 51

Страница: 51 / 84

This procedure is used to verify and fine-tune the flowmeter

calibration. Every flowmeter is calibrated with water at the

factory and stamped with a calibration val ue. Enter that value

as a starting point and use this pro ce dure to fine-tune that

value for your specific in stal la tion and spray ing application.

This procedure should be re peat ed each time a new solution

is being applied

(differ ing so lu tions will have a different

spe cif ic gravities and different flow char ac ter is tics)

or when

the flowmeter in stal la tion has been altered.
Controller 1 and Controller 2 each have their own flowmeter.

The following procedure

(Illustrations)

show the required

switch settings for either controller, denoted by Ch1 or Ch2.

PROCEDURE

1. Put enough water in the sprayer tank to perform this test.

(Preferably 100 gallons or more. The larg er the volume of

water used, the more accurate will be the calibration.)

2. Start sprayer pump and turn on booms. Run enough

water to purge all air from lines. Turn off booms but

leave pump running.

3. Turn console rotary selector to the VOLUME po si tion.

Select the counter (1-3) that you want to use. Press and

hold the RESET button until the dis play reads 0.

4. Turn on all booms, and run a known amount of water

(preferably 100 gallons or more).

For Ch1:

Turn on all booms, and set Ch1 switch to MAN.

For Ch2:

Set Ch2 switch to MAN (turns single boom on).

Ch1 much be set as shown in Ch2 illustration.

5. Put the controller in Hold:

For Ch1:

Set the Ch1 switch to MASTER HOLD.

For Ch2:

Set the Ch2 switch to OFF (turns single boom off).

Compare the console’s VOLUME reading with the known

amount of water run. If the two amounts are within one

or two percent, no fine tuning is required. If the two

amounts are more than two or three percent different,

continue with the next step.

6. With the console still in the VOLUME position, enter

calibration, hold the CAL button until red warning light

comes on; about one second). The dis play will show the

flowmeter calibration value and the CAL icon.

7. Momentarily press the CAL button. The CAL icon will

begin to flash and the total volume will be displayed.

See Illustrations.

8. When the TOTAL FLOW value is displayed, use the “+” or

“-” button to adjust the value to match the amount of

water run.

9. Momentarily press the CAL button. The CAL icon and

the flowmeter calibration number will be displayed.

You will notice that the flowmeter calibration value has

changed. Write down the new flowmeter calibration

value. This is your

“fine tuned”

calibration value, keep it

for future reference.

10. Exit calibration by holding the “CAL” button until the red

warning light goes out (about one second).

The most accurate method to measure the volume of

water run is to place a container under EVERY nozzle and

add together the amount from each nozzle. This assures that

100 percent of the water is collected and that all nozzles are

spraying equally. It is important to perform this pro ce dure

at a flow rate similar to that which will be used in the field. It

is also possible to disconnect the main boom line and run it

to a large measuring container but a valve must be installed

and properly adjusted to simulate actual field conditions.

Appendix C

Fine Tuning Flowmeter Calibration Value

(If system is set up for NH3 application, see page 70)

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

INLINE

BYPASS

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

OFF

CONTROLLER 1 B O O M S

OFF

CAL

CONT

SEL

RESET

CONTROLLER 1

APPLICATION RATE 2

TANK

___

CONTROLLER 2

APPLICATION RATE 1

AUTO

MAN

OFF

AUTO

MAN

MASTER

HOLD

MANAUTO

CAL

HOLD

CAL

Ch1: “Fine Tuning” Flowmeter

Ch2: “Fine Tuning” Flowmeter

For Ch2 tuning to work, Ch1 must be set as follows:

•

All Ch1 booms must be OFF

•

Ch1 switch must be set to Run (i.e. not MasterHold)

Ch1

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

INLINE

BYPASS

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

OFF

CONTROLLER 1 B O O M S

OFF

CAL

CONT

SEL

RESET

CONTROLLER 1

APPLICATION RATE 2

TANK

___

CONTROLLER 2

APPLICATION RATE 1

AUTO

MAN

OFF

AUTO

MAN

MASTER

HOLD

MANAUTO

CAL

Ch2

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды