micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 18

Страница: 18 / 84

Magnets

Please read the following information about magnet spacing

and polarity.
The number of magnets that must be used depends on

the size of your tire and where you mount the sensor. On

tractor or implement wheels the general rule of thumb is one

magnet for each wheel bolt (minimum of two, and always an

even number). For drive shafts or small wheels (ATV’s), two

magnets are usually adequate.
Some installations may require that more than two magnets

be installed. To determine the number of magnets required,

measure the distance traveled of one revolution of the

sensor equipped wheel in inches (centimeters).
See the following tables to find the minimum number of

magnets required (always an even number)

Installation

(cont)

Speed Sensor Installation

Installation Note: The console provides one connection point

for the speed sensor. A 15 ft. extension cable is provided.

For speed sensor installations on implements, add 3-pin

extension cables as required.

Please Note: If you have purchased an Astro II GPS speed

sensor, Vansco radar or other radar or GPS speed sensor,

disregard the following section on magnetic speed sensors

and install the speed sensor as described in the instructions

included with the unit. You may need an adapter cable to

connect to radar or GPS Speed Sensor, see Appendix H.

Locations where the sensor may be installed:
1. Non-driven wheel on tractor, vehicle or implement. This is

less susceptible to errors resulting from wheel slip.

Locate the following parts:

•

Speed sensor cable (Green body)

•

Mounting “L” bracket

•

Magnets

•

Cable ties

2. Tractor, vehicle or planter drive shaft. This type of

mounting is recommended for trucks, four-wheel drive

tractors or other equipment that has poor or no access to

a non-driven wheel.

See Appendix A for magnetic speed

sensor installation details for various types of wheels or

drive shaft.

The magnets provided by Micro-Trak are marked with a

punched dashed line on the SOUTH pole side of the magnet.

See Illustration below.

Always use an even number of magnets, and always alternate

the polarities of the magnets as you go around the wheel

hub or drive shaft.
To install, mount the first magnet with the SOUTH pole side

(dashed line) facing toward the hub or shaft. Mount the

second magnet with the NORTH pole side facing toward the

hub or shaft.

See Illustration below.

For proper operation, the magnets must be evenly spaced

around the wheel or drive shaft. The magnets must be at

least 1” apart.

See Illustration below.

NOTE: Magnets may be attached mechanically or adhered

with epoxy or other high quality adhesive. When using

adhesive, thoroughly clean the area of dirt and oil.

English or Turf (inches)

Wheel Circumference

80 120 160 200

Number of Magnets

Metric (cm)

Wheel Circumference

100 200 300 400 500

Number of Magnets

North

South

Test magnet

should alternately

attract and repel.

1” Minimum

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды