micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 43

Страница: 43 / 84

If there is no response from any of the following tests, refer

to the main wiring diagram to locate the next connector in

line to ward the con sole and repeat the test at that con nec tor.

If there is a response at that connector, the problem may be

in the cable between the two connectors (or the con nec tors

themselves).

SPEED INPUT

Turn rotary switch to speed po si tion and dis con nect the

speed sensor (yel low tie) from the main harness. Check

for 12 volts between pins B (white) and C (black) of the

main harness speed cable (yellow tie). Using a clip lead

or other jumper wire (such as a paper clip bent in a “U”),

several times rap id ly short to geth er pins A (red) and C

(black) of the 3-pin connector

(See Illustration below).

The console should respond with some speed read ing.

FLOW INPUT

Turn rotary switch to VOLUME/MINUTE and disconnect

the flow sen sor (green tie) from the main harness. Check

for 12 volts be tween pins B (red) and C (orange) of the

main harness flow cable (green tie). Using a clip lead or

other jumper wire (pa per clip bent in a “U”), several times

rapidly short together pins A (brown) and C (orange) of

the 3-pin connector. The con sole should re spond with

some flow rate reading.

REMOTE RUN/HOLD INPUT

Grounding the grey run/hold wire should turn on the

“HOLD” icon on the console’s left display, and display

“HOLD” on the console’s right display. Disconnecting

the grey wire should remove the “HOLD” messages

(console run/hold switch in “RUN”).

FLOWMETER

Shaking the Flowmeter end to end should pro duce a “rattling”

sound (shaft end play). Blowing in the meter from either end

should spin the turbine freely. If the turbine spins freely but

the meter will not register flow with a known working sensor,

the turbine may be defective.

See Flow me ter Assembly and

clean ing on page 54 for details.

Troubleshooting

(cont)

Console Inputs

SERVO VALVE CONTROL SIGNAL

With the console turned ON, put the console in MANUAL

mode, place the remote Run/Hold switch in the RUN position

and turn at least one boom switch to ON. Using a voltmeter

or simple test light, check from a good frame ground to each

of the servo wires on the main harness connector. You should

get 0 volts on each wire. Holding the “+” button should cause

one wire to pulse toward 12 volts (light will pulse). Holding

the “-” button should cause the other wire to pulse toward 12

volts (light will pulse).

SERVO VALVE

The best way to test the servo valve is with a known working

console. Turn console ON, put the console in MANUAL mode,

place the remote Run/Hold in the RUN position, turn the

rotary switch to RATE and turn at least one boom switch to

ON. With the servo valve connected to the servo valve lead

on the main harness, holding the “+” button should close

the servo valve and holding the “-” button should open the

servo valve.

NOTE: Assuming you are in bypass configuration (provided

the console has passed the Servo Valve Control Signal

test). The servo valve should operate smoothly in both

directions, from fully open to fully closed.

You may also use a 12-volt battery or a 9-volt battery.

Connecting the battery to each terminal on the servo valve

should cause the servo valve to run in one direction. Reversing

the battery connections should cause the servo valve to run

the other direction. The servo valve should operate smoothly

in both directions, from fully open to fully closed.

PLUMBING

Proper plumbing is a very important factor in obtaining

optimal performance from your MT-3405D system. The chart

on the next page will help you determine what area of the

plumbing may be causing your problem. At this point, it is

assumed that your plumbing basically matches that of the

system diagram and that the servo valve and flowmeter are

known to be installed correctly and functioning properly. In

addition, make certain that you have selected and installed

the correct spray tips for the application, speed and spray rate

that you intend to maintain. Don’t forget the obvious such

as leaky fittings and hoses, pinched hoses and plugged or

worn nozzles.

If you need more detail than the chart provides,

please refer to Plumbing Guidelines on pages 45-46.

Three-Pin Connector

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды