micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 19

Страница: 19 / 84

The magnets are attached to a wheel hub or drive shaft and

the speed sensor is mounted directly over the magnet. When

the wheel or drive shaft begins turning, a speed impulse is

sent to the MT-3405D console every time a magnet passes by

the tip of the speed sensor. For the speed sensor to operate

properly, the spacing between the magnets and the tip of

the sensor must always remain constant. Before permanently

mounting any parts, be sure that the location you have

selected will meet the requirements shown in

Illustration to

the right.

NOTE: Observe magnet polarities (see previous section).

Installation

(cont)

Attaching the Speed Sensor

Magnet

Sensor

(Green body)

1/4” to 1/2” air gap

3/8” nuts

45° max.

Bracket must

be rigidly

mounted.

Sensor assembly must

not be mounted

more than 45° from

per pen dic u lar

Connecting the Speed Sensor Cable

The speed sensor cable has a GREEN sensor body and mates

with the 3-pin connector which is marked with a yellow cable

tie. The speed sensor and the flow sensor are identical, but

must be connected to the proper harness connector. The

speed sensor always connects to the 3-pin M/P connector

with the YELLOW tie and flow sensor always connects to the

3-pin M/P connector with the GREEN tie.

See MT-3405D

Wiring Diagrams on pages 12 and 14.

The optional Run/hold sensor, also uses the same type of

connector as the speed and flow sensors. However, the Run/

hold sensor has a GRAY tie near the 3-pin connector, the

sensor body is BLACK, and it always connects to the main

harness lead with the GRAY tie.

See MT-3405D Wiring

Diagrams on pages 12 and 14.
* See Appendix L for required adapter if using the remote

speed connection on the Ch2 harness.

SENSOR IDENTIFICATION CHART

SENSOR

SENSOR BODY COLOR

MAIN HARNESS TIE COLOR

Speed

Green

Yellow

RPM

Black

None

Run/Hold

Black

Gray

Vansco Radar Speed Sensor

Astro 5 GPS Speed Sensor

Speed Sensor Options

In addition to the standard Hall-effect magnetic speed

sensor, the MT-3405D may be interfaced with a va ri ety of

other speed sensing equipment. Several options are listed

below.

Astro Series or Other GPS Speed Sensor Interfaces

The MT-3405D may also be used with most GPS speed

sensors that output a pulsed signal, such as the Micro-Trak

Astro II and 5, SkyTrak or Dickey-John GPS speed sensors. An

adapter cable may be required.

Vansco™ Radar Speed Sensor

The Vansco radar speed sensor uses a microwave (radar)

signal to deliver a reliable, accurate speed signal for electronic

equipment. It features state-of-the-art electronic design/

manufacturing, rugged aluminum housing and complete

testing and certification.

Radar Interface

The MT-3405D may also be interfaced with most popular

radar ground speed sensors. An adapter cable is re quired for

proper interface.

SEE APPENDIX H FOR LIST OF ADAPTER CABLES FOR RADAR.

Contact a Micro-Trak sales representative for de tails on
any of these products, or call Mi cro-Trak Systems, Inc. at
1-800-328-9613.

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды