micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 46

Страница: 46 / 84

Plumbing Guidelines

(cont)

Valve Purpose and Adjustments

TANK SHUT-OFF VALVE

The tank shut-off valve is for convenience only. It allows you

to work on the plumbing without draining the tank. It should

always be fully open during operation.

AGITATION SHUT-OFF VALVE

The agitation shut-off valve is mostly for convenience. It

allows you to work on the plumbing without draining the

tank. It should normally be fully open during operation.

PRESSURE RELIEF VALVE

The pressure relief valve is used to avoid excessive pressure

when the booms are turned off. Start with the handle screwed

mostly out. Slowly bring pump up to operating RPM (make

sure pressure does not go too high). Put the MT-3405D in

MAN and turn boom on. Hold adjust switch to “+” for about

30 seconds to fully close servo valve. Turn booms OFF. Now

slowly screw handle in until maximum desired pressure is

reached. Lock handle in place with locking nut or collar.

Note: Spraying Systems 144H DirectoValve has a maximum

pressure rating of 100 PSI (7 bar).

RANGE ADJUST VALVE

The range adjust valve is required when the pump is much

larger than necessary. When the range valve is opened, some

of the liquid will be bypassed around the pump to avoid

“overloading” the rest of the system. The setting of the range

adjust valve is determined by the throttle valve.

Start with

the range valve fully closed and perform the Pre-field System

Checkout on pages 38-39.

If the throttle valve needs to be

more than two thirds closed, open the Range valve slightly
and perform the Pre-field System Checkout again.

THROTTLE VALVE (BYPASS PLUMBING)

The throttle valve limits your high end to maximize servo

performance.

Start with throttle valve fully open and perform

the Pre-field System Checkout on page 38-39.

EXAMPLE

With the throttle fully open and servo fully closed,

you may be able to get 50 GPA at 5 MPH when you

only want 25 GPA. If you were to simply open the

servo you may be able to get down to 25 GPA, but

if your speed should drop to 3 MPH, the servo can’t

open any farther and won’t be able to maintain 25

GPA. Therefore, if you leave the servo closed and

close the throttle until your high end has dropped

from 50 GPA to about 30 GPA, the servo has a

greater operating range.

The throttle valve pictured in the system diagram

is a needle valve (Spraying Systems Type 12690

or 12795). A ball valve may be used but is more

difficult to adjust and keep adjusted. Do not install a

pressure regulator or relief as a throttle valve.

If the throttle valve is closed too much, PSI may

fluctuate greatly in AUTO.

RELIEF SOLENOID VALVE

The optional relief solenoid will ensure enough bypass to

avoid excessive pressure when the boom valves are turned

OFF.

See page 23.

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды