micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 52

Страница: 52 / 84

IMPORTANT: Opening the flowmeter will void the Flowmeter

Calibration value assigned to your unit. However, you may

need to take the flowmeter apart for periodic cleaning or

to remove an obstruction.

If you can shake the flowmeter from end-to-end to produce

a “rattling” sound (shaft-end play), or if you can blow into the

meter from either end and cause the turbine to spin freely,

your flowmeter does not need cleaning. If you cannot hear

the “rattling” sound or get the turbine to spin freely, your

flowmeter needs to be cleaned.

See Illustrations below for

reassembly instructions.

OPENING THE FLOWMETER

Cut the calibration tag retaining wire. Remove the screws

and disassemble the flowmeter. Do not attempt to remove

the sleeve bearings from the flowmeter housing.
Use warm water and if necessary, a mild detergent and a

soft bristle brush to clean all parts. Do not use solvents or

diesel fuel to clean the flowmeter. A magnet works well for

removing fine metallic particles from the turbine.
Inspect all parts. Check for excessive bearing or shaft wear.

The shaft will wear shorter until the turbine drags on the

housing.

Illustration 19

shows you what a new shaft looks

like. When the shaft is worn to the point of drag, the turbine

must be replaced.
On a flat surface, place each housing half on end. Set and

spin the turbine in each half. It should spin freely. If it does

not spin freely, remove the turbine, wipe the shaft and try

again. If is still does not spin freely, the shaft or bearings may

have excessive wear.

(Service may be necessary).

ASSEMBLING THE FLOWMETER

Stainless steel meters use a Teflon gasket. Sealants are

normally not required. Plastic meters use an o-ring (Quad-

ring). Apply a small amount of silicon grease for lubrication.

Gaskets and o-rings may be reused several times but

eventually may need replacement.
Place the turbine in the non-sensor housing. Position gasket

/ o-ring; carefully place sensor housing over turbine. Drop all

screws into holes. Hold nuts (and lock washers on stainless

meters) in place and finger-tighten screws. Ensure proper

placement of gasket / o-ring and evenly tighten all screws.

Attach tag.
After assembly, shaking flowmeter end-to-end should

produce a “rattling” sound (shaft end play). Blowing into

the meter from either end should cause the turbine to spin

freely. If the turbine only spins from one direction, install the

flowmeter so that the liquid flows in that direction.

(Service

may be necessary).

For maximum accuracy the flowmeter should be mounted

in a vertical position. Recalibration is required before field

operation.

Appendix D

Flowmeter Assembly

Housing FM750 GFN

Turbine

P/N 14836

Quad-ring

P/N 13783

Housing FM750 GFN

(Non Sensor)

Complete assembly

FM750 GFN Flowmeter

Housing FM750 SS

Turbine

Gasket

Housing FM750 SS

(Non Sensor)

Complete assembly

FM750 SS Flowmeter

New Shaft

Illustration 19

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды