micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 36

Страница: 36 / 84

Use

CONT SEL

button to view either Ch1 or Ch2 data.

(See the NH3 section in the Appendix (F) for NH3 data

description.)

RATE:

Actual number of gallons per acre (liters per hectare)

being applied.

TANK:

Amount (gal or lit) remaining in tank.

VOLUME/MINUTE:

Flow rate in GPM (LPM).

Three independent pairs of counters.

In either the AREA or the VOLUME

position, select a pair of counters by

pressing the “+” button. The active pair of counters (1,2,3) is

indicated by the small numbers in the lower right corner of

the left-hand display. DO NOT attempt to select the counter

pair by using the “-” button because it will reset the selected

counter pair to zero.

See additional data description to the

right and see RESETTING SYSTEM COUNTERS section.

VOLUME (1) (2) (3):

AREA (1) (2) (3):

)

Operation

(cont)

Data Displayed in Rotary Switch Positions

VOLUME (1) (2) (3):

Total gallons (liters) applied since the

active counter was last reset to zero.

AREA (1) (2) (3):

The acres (hectares) covered since the

counter was last reset to zero. The area counters do not

accumulate area when the console is in HOLD or if all booms

are turned OFF.

DISTANCE:

The feet (meters) driven since the counter was

last reset to zero. This counter does not accumulate when

the console is in HOLD. This counter may be reset to zero

independent of other system counters.

AREA/HOUR:

Rate of coverage in acres/hour (hectare/

hour).

SPEED:

Ground speed in miles (kilometers) per hour.

IMPORTANT: all booms automatically shut off if system is in

“HOLD” or if in AUTO with NO SPEED.

After the “-” (RESET) button has been held for 1 second, the

“CLEAr” message will be replaced by “.0”, indicating that

counter pair #3 has been cleared.

Note: Both Ch1 and Ch2 have their own (3) independent

sets of counters.

Clearing System Counters

When the desired counter number is displayed, press the

“-” (RESET) button and “CLEAr” will be displayed. If the

“-” button is released before 1 second has elapsed, the

counters will not be cleared and the “CLEAr” message will

be replaced with the previous total.

NOTE: holding the “-” (RESET) button for 1 second will

clear both the #3 AREA counter and the #3 VOLUME

counter whether the rotary switch is in the AREA or the

VOLUME position.

HOLD

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

INLINE

BYPASS

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

AREA /

HOUR

VOLUME

(1) (2) (3)

RATE

SPEED

AREA

(1) (2) (3)

OFF

CONTROLLER 1 B O O M S

OFF

CAL

CONT

SEL

RESET

CONTROLLER 1

APPLICATION RATE 2

TANK

___

CONTROLLER 2

APPLICATION RATE 1

AUTO

MAN

OFF

AUTO

MAN

MASTER

HOLD

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды