micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 22

Страница: 22 / 84

If you have a positive displacement pump or a cen trif u gal

pump capable of generating excessive pressure, you must

in stall a pressure relief valve and adjust it to a safe max i-

mum pressure. If a positive dis place ment pump is operated

without a pressure relief valve, damage may re sult to pump

or other plumbing component.

See Illustration to the right.

Range Adjust Valve

With oversized pumps, it may be necessary to install a range

adjust valve. The range adjust valve will reduce the pump’s

output to the rest of the system.

Ad just ment of this valve

is covered in the Pre-Field System Checkout, pages 38-39.

See Illustration to the right.

Servo, Throttling Valves

For

BYPASS

installations, the servo valve installs in an

unrestricted return line to the inlet of the pump or directly

into the tank. The console must be calibrated for bypass

operation,

see Calibration Section.

DO NOT

install the servo

valve closer than 12” to the flowmeter. The servo valve has a

flow direction decal on it. Make certain that the actual flow

direction matches the decal on the servo valve.

DO NOT

install the servo valve in the agitation line. Slow response

time and marginal operation may result. The return line

should tee from the main line just after the throttling valve.

See Illustration to the right. The throttling valve is used to

limit the output (set maximum output) of the pump to the

flowmeter and servo valve. The throttling valve is adjusted

to put the servo valve in its optimal operating range.

Please

refer to Pre-Field System Checkout on pages 38-39 for proper

valve adjustment procedure.

The servo valve connects directly to the 3-pin connector on

the main harness. If more length is required, use a 3-pin W/P

extension cable of the appropriate length.

IMPORTANT NOTE: If using the MT-3405D with an old style

Micro-Trak servo valve, the valve voltage must be set to 8

volts.

See Special Calibration Valve Voltage section on page

31.

NOTE:

The servo valve may be installed in the main spray

line as shown in

Illustration 10.

For in-line installations, you

will need to calibrate the system for

INLINE

operation,

see

page 28.

For positive displacement pumps

For oversized pumps

Tee “C”

Tee “A”

Pressure

Relief Valve

Tee “C”

Range

Adjust Valve

Tee “A”

Installation

(cont)

Manual Pressure Relief Valve

Return to pump

inlet or unrestricted

return to tank

Servo Valve Cable

From Pump

Throttling Valve

To Flowmeter

Servo Valve

BYPASS

Servo

Flowmeter

From Pump

INLINE

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды