micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 23

Страница: 23 / 84

MT-3405D Boom Connections

Boom Shut-off Valves

Boom valves of differing designs may require a “T” fitting.

Make certain to use adequately sized plumbing lines to avoid

ex ces sive pressure drops.

DO NOT

install the shut-off valves

closer than 12” to the flowmeter.
Locate the boom shut-off harness. The boom wires are color-

coded.

(If valves have wires, crimp terminals on those wires.)

Attach the cables to the terminals on the boom valves.

Attach a ground terminal to each valve. If valves operate

backwards, reverse connections. Apply silicone grease to the

ter mi nal connections to help prevent corrosion and insure a

good electrical con nec tion.

IMPORTANT: See complete wiring diagrams on pages 12 and 14.

NOTE: to configure your system using motorized ball valves,

see Appendix G.

Care & Maintenance of your MT-3405D Console

Store the console in a cool dry location if it will not be

used for an extended period of time, such as during the

off-season.
As with any electronic equipment, use care in cleaning so

that water or other liquids do not enter the case.
Thoroughly rinse Flowmeter with clean water, install

plastic shipping plugs and keep from freezing.

PRECAUTIONS

•

The input pressure on the glass-filled nylon flowmeter

FM750 GFN should not exceed 150 PSI (1034 kpa).

•

Do not expose the flowmeter to liquid temperatures

exceeding 130 degrees F (55 degrees C).

•

Some chemicals may damage the Noryl turbine or the

nylon body of the flowmeter. If you are in doubt,

contact the chemical manufacturer.

The relief valve is used to “dump” pressure when your boom

valves are turned off. Whenever all the boom control switches

are turned off, or when HOLD is selected with the master

switch, the relief valve should be open. Use illustration as

your pattern for proper installation if your relief valve has a

flow-through port.

DO NOT

install the relief valve closer than

12” to the flowmeter. With the relief valve installed, locate

the violet wire (tied back on flow/servo cable) and crimp a

female terminal on the violet wire and connect to relief valve

terminal. Connect other terminal on relief valve to ground.

*FUSE HOLDER AND TERMINALS

INSTALLED BY USER

+12 VDC

GND

BLUE

GND

AUX PWR ORANGE

BOOM 1

YELL

BOOM 2 BROWN

BOOM 3 GR

BOOM 4 BL

ACK

BOOM 5 RED

HEAT

SHRINK

VIOLET WIRE

DETAIL A

DETAIL B

SPEED

GROUND

VIOLET WIRE

Installation

(cont)

Electric Relief Valve (Ch1 only)

NOTE:

The relief valve output

is only available on the Ch1

wiring harness.

If your relief valve does not have flow-through port, you must

add a “T” fitting.

NOTE: To assure a good connection and

avoid corrosion, coat electrical connections with silicone

grease.

“T” Fitting

Servo

Valve

Relief

Solenoid

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды