micro-trak DUAL CONTROL MT-3405D Скачать руководство пользователя страница 68

Страница: 68 / 84

Always follow accepted safety precautions. Make sure that

equipment is in good operating order. Before connecting

the nurse tank to the applicator, check the electric shut-off

valve of the MT-3405D system for proper operation.
After changing nurse tanks or after other periods of long

shut-down, operate the system in MAN until the application

rate stabilizes. This allows the heat exchanger to reach

operating temperature before selecting AUTO. Erratic

operation may be experienced if AUTO is selected before

operating temperature is reached.
Manifold pressure is very important for good distribution

of NH3. Use barbed fittings with properly sized orifices or

an adjustable manifold to maintain adequate pressure. If

manifold back pressure is too low, proper cooling will not

be achieved, vapor bubbles will be allowed to enter the

flowmeter, and readings will be inaccurate. Typical manifold

pressure ranges from 15 to 60 PSI (1 to 4 bar) depending

on application rates and ambient temperature. If manifold

pressure stops climbing but FLOW RATE continues to climb,

vapor bubbles are present.

Additional Troubleshooting Tips for NH3:

See Troubleshooting section, starting on page 40.

Appendix F

(cont)

MT-3405D - NH3 Specific

(cont)

Field Operation - Troubleshooting for NH3

In hilly or rough conditions the nurse tank dip tube will not

remain submerged, allowing extra vapor in the system. This

vapor is to too much for the heat exchanger to condense

and the system will exhibit erratic operation. If the dip tube

remains out of liquid, operation may appear to be normal,

but the system is simply metering vapor. If this occurs, you

will notice extremely low manifold pressure. Change tanks

before the NH3 level is low enough to cause these problems.
In NH3 control systems, location of the frost build-up is an

indication of system performance. The NH3 kit will normally

have frost on the output side of the servo valve and in some

cases, a small amount on the bottom portion of the heat

exchanger. Frost before the servo valve indicates excessive

pressure drop in the delivery system or restricted vapor lines.
The strainer is a common source of excessive pressure

drop and should be cleaned regularly. AFTER COMPLETELY

DRAINING THE SYSTEM, remove the large plug and carefully

clean the strainer’s screen. Also, periodically check the vapor

tubes for obstructions.

Содержание DUAL CONTROL MT-3405D





















































































Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды

micro-trak DUAL CONTROL MT-3405D, Справочное руководство

Результаты поиска

Содержание DUAL CONTROL MT-3405D

Отзывы:

Похожие инструкции для DUAL CONTROL MT-3405D

Бренды по названию

Популярные бренды