Metos PROVENO E Скачать руководство пользователя страница 65

Страница: 65 / 72

PROVENO E

Rev. 1.2 (24.08.2016)

Troubleshooting

7. Troubleshooting

MALFUNCTION

POSSIBLE CAUSE

WHAT TO DO

The kettle cannot be
switched on

The mains switch is in the OFF position

Turn the mains switch ﬁ tted on the rear part of the
control pillar right side to the ON position

The emergency/stop button is pushed

Release the emergency-stop switch by turning it
clockwise

The fuses in the main fuse box areblown/
triggered

Change/excite the fuses

The delivery of electric energy is interrupted

Check if the delivery of electric energy is interrupted
elsewhere and wait for it to return

The kettle does not heat

The timer function is activated if the kettle is
equipped with a timer

Switch off the timer function according to instructions

The EasyRun function is activated if the kettle
is equipped with the option

Switch off the EasyRun function according to instruc-
tions

The emergency/stop button is pushed

Release the emergency-stop switch by turning it
clockwise

The ON/OFF switch is not in the ON position

Push the switch to the ON position

On a kettle ﬁ tted with automatic cooling: The
draining of the cooling water is still unﬁ nished

Wait until time on the display next to the cooling but-
ton runs out

The fuses in the main fuse box are blown/
triggered

Change/excite the fuses

The kettle is not returned to an upright position
after tilting, the temperature display shows a
'PoS' signal

Press the tilting reverse button until the kettle is to-
tally horizontal and the temperature display shows an
'On' signal

Electric kettle: Not enough water in the steam-
generator, the two red error lights on the cont-
rol panel are illuminated

Check that the shut-off valve of the water supply line
is in the OPEN position

Steam kettle: The shut-off valve of the steam
input is closed

Open the valve

Other technical fault

Contact qualiﬁ ed technical personnel

Heating of the kettle is
slow

Electric kettle: Too much water in the steam-
generator

Check the water level of the steam generator accor-
ding to the instructions by opening the emptying valve.

Steam kettle: Condensate water gathered in
thesteam jacket has not been emptied

Remove the condensate by opening the emptying
valve which is in the steam jacket

The steam jacket of a kettle equipped with a
manual cooling system (C1) is full of cooling
water which has not been emptied

Remove the chilling water by opening the emptying
valve (electric) or the emptying valve for condensate
(steam)

There is air in the steam jacket which does
ﬂ ow out because the automatic vacuum valve
does not function

If the air does not exit through the automatic vacuum
valve, contact qualiﬁ ed technical personnel

One of the fuses in the main fuse box is
blown/triggered

Change/excite the fuse

The forced 1/2-power control of the building is on Normal operation

Other technical fault

Contact qualiﬁ ed technical personnel

Содержание PROVENO E









































































Результаты поиска

Содержание PROVENO E

Отзывы:

Metos PROVENO E, Инструкция по установке и эксплуатации, Страница: 65 / 72

Результаты поиска

Содержание PROVENO E

Отзывы: