Metos PROVENO E Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 72

Metos PROVENO E Скачать руководство пользователя страница 17

|

17

PROVENO E

Rev. 1.2 (24.08.2016)

Functional description

3. Functional

description

3.1. Intended use of the appliance

The Proveno combi-kettle is designed for professional food preparation. Using Proveno for other purpo-
ses is prohibited. It is forbidden to put corrosive ingredients or substances reacting with each other in the
kettle. Please observe that long-term effect of some substances used in food preparation is corrosive.
Such substances are, for example, salt, acetic acid, citric acid and lactic acid.

3.1.1. Use for other purposes

The manufacturer does not take responsibility for functional troubles or damages caused by misuse or
use for other purposes than stated above.

3.2. Construction

The construction of the kettle is of stainless steel throughout (AISI 304). The inner bottom and jacket are
of acid-proof steel (AISI 316). The kettle is triple-jacketed and thermally insulated throughout.

3.3. Operating

principle

The Proveno kettle is heated by steam generated with heating elements. The steam generator and hea-
ting elements are located in the lower section of the kettle.

The kettle tilts by means of a tilting motor (40-150-litre kettles). Larger kettles (200-400 litres) are equip-
ped with a hydraulic tilting mechanism. The mixing functions are performed by means of a gear motor.
Cooling (accessory) is based on cold water circulating inside the kettle’s steam jacket. The raised control
panel of the appliance is situated on the kettle’s right-hand pillar (control pillar).

«
...
15
16
17
18
19
...
»

Содержание PROVENO E









































































Отзывы:

Нет отзывов