manualshive.com logo in svg

Metos PROVENO E, Инструкция по установке и эксплуатации, Страница: 45 / 72

Поделиться
Скачать
Metos PROVENO E Скачать руководство пользователя страница 45

| 

45

PROVENO E

Rev. 1.2 (24.08.2016)

Installation

5. Installation

5.1. General

Please observe the instructions given in this chapter concerning the installation and adjustments that 
must be done before taking the Proveno combi-kettle into use. Strict observance of the instructions 
prevents malfunctions and damages potentially caused by defective installation.

Do not switch the power on if the installation place is damp or wet (building site conditions).

5.1.1. Operating conditions

The Proveno combi-kettle can be used in a normal, air-conditioned professional kitchen. The room tempe-
rature of the installation place must not 40°C and the relative humidity must be less than 80% 
(condensation on surfaces not allowed to occur). If the temperature of the facility in winter conditions is 
below 0°C, the steam generator of the combi-kettle must be drained and the kettle must be emptied to 
avoid damage caused by freezing. The kettle’s pipes and solenoid valve bodies must be emptied at the 
same time.

5.1.2.  Possible interference from the surroundings (to the surroundings)

The Proveno combi-kettle fulfi ls the requirements of the EMC directive concerning the emissions and 
immunity to electromagnetic disturbances. In case there are electronically controlled appliances and, 
in particular, devices fi tted with a frequency converter in the installation place, it is recommended to 
ensure their conformity with the relevant regulations and that their cabling has been done according to 
instructions.

5.1.3. Storage

The Proveno combi-kettle must be stored in a dry place, at a temperature b10 and +40°C. The 
kettle should be kept in its transport package during storage.

If the appliance is stored in construction site conditions, special care must be taken not to damage it 
through other operations on the site.

•  Protect the exterior of the combi-kettle from scratches and knocks.

•  Protect the combi-kettle from construction site dust.

•  Protect the combi-kettle from sparks produced by welding, grinding and abrasive cutting 

wheels. These can later cause rust spots on the stainless steel surface of the appliance.

5.1.4.  Unpacking the appliance

The combi-kettle should be transported in its own package as close as possible to the installation place 
before fi nal unpacking. Do not remove the protective foils until after installation, just before the fi rst use 
of the kettle.

After removing from the transport pallet, the combi-kettle is not stable until it has been bolted down to 
the installation frame. It is strictly forbidden to operate or tilt the kettle before it has been fi xed to the fl oor 
according to the installation instructions. When the combi-kettle is removed from its transport pallet, it 
must be supported to prevent it from falling before it is fi xed to the fl oor. If the kettle falls down, this may 
cause injury to people or damage to property.

Содержание PROVENO E









































































Отзывы:

Нет отзывов