manualshive.com logo in svg

Metos PROVENO E, Инструкция по установке и эксплуатации, Страница: 28 / 72

Поделиться
Скачать
Metos PROVENO E Скачать руководство пользователя страница 28

28

 |

PROVENO E

Rev. 1.2 (24.08.2016)

Operation instructions

4.2.8.  Mixing while tilting

This option enables forced mixing at the lowest mixing speed while the kettle is tilted. With the help of 
this function it is possible to portion more homogenous batches of food into smaller bowls.

The user parameter Pr22 must be set to ON to enable this feature.
For safety reasons, the mixer only operates at the lowest speed of 15 rev./min. The central dial must be 
held down.

Do as follows:

•  Lift the kettle lid to an upper position.

•  Tilt the kettle slightly from the cooking position.

•  Press the central dial 

 and 

keep it pressed all the time

.

•  Using a fi nger of your other hand, press the mixing function button 

•  Press the mixer start button 

=> The mixer starts to run at a speed of 15 rev./min. It is not possible to raise the speed.

•  Continue to keep the central dial pressed.

•  Press the tilting button  

 with a fi nger of your other hand.

=> The kettle tilts and the mixer runs all the time at a speed of 15 rev./min.

If the kettle is returned fully to the cooking position the mixer stops.

Release the central dial when you want to stop this function. To operate mixing functions after that, close 
the lid and put the safety grid on the kettle according to instructions.

4.2.9.  Manual water fi lling

Filling a small amount of water:

 Press and keep pressed.

When the desired amount of water has been fi lled release the button.

Filling a large amount of water:

 Press once

The water fl ow starts.When the desired amount of water has been fi lled, 

 Press again once.

The water fl ow stops

Содержание PROVENO E









































































Отзывы:

Нет отзывов