Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 92

Страница: 92 / 159

OIL INJECTION PUMP PURGE

Before starting the engine after changing the in‑line oil filter, the oil injection

pump must be purged. This will remove any air that may be in the pump, oil

supply hose, or internal passages.

a -

Oil injection pump

b -

Oil supply hose

IMPORTANT: Fill the engine fuel system with fuel before purging the oil

injection pump.

1. Fill the engine fuel system with fuel. Connect the fuel hose and squeeze

the primer bulb until it feels firm.

19779

2. Turn the ignition key switch to the ON position.

26846

3. Within the first 10 seconds after the key switch has been turned on, move

the remote control handle from neutral into forward gear 3 to 5 times. This

will automatically start the purging process.

NOTE: It may take a few minutes for the pump to complete the purge process.

7912

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 92 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: