Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 81

Страница: 81 / 159

7. Do not advance the neutral fast idle speed feature on the remote control

for starting.

27242

8. Turn the ignition key to "START" position. Release the key when the

engine starts. If the engine fails to start in 10 seconds, return the key to

"OFF" position, wait one second and try again.

19804

NOTE: The electronic starting system will automatically prime (choke) the

engine and increase idle speed for starting.

9. Check for a steady stream of water flowing out of the water pump

indicator hole.

IMPORTANT: If no water is coming out of the water pump indicator hole, stop

the engine and check cooling water intake holes for obstruction. No

obstruction may indicate a water pump failure or blockage in the cooling

system. This condition will cause the engine to overheat. Have the outboard

checked by your dealer. Operating the engine while overheated will cause

engine damage.

19805

GEAR SHIFTING

IMPORTANT: Never shift the outboard into gear unless the engine speed is at

idle.
Your outboard has three gear shift positions to provide operation: forward (F),

neutral (N), and reverse (R).
When shifting, always stop at neutral position and allow the engine speed to

return to idle.
Always shift the outboard into gear with a quick motion.

OPERATION

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 81 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: