Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 87

Страница: 87 / 159

•

Inspect the carbon fiber reeds for chipping or cracks.

EVERY 300 HOURS OF OPERATION

•

Replace the in‑line oil filter every 300 hours of operation.

BEFORE PERIODS OF STORAGE

•

Refer to

Storage

section.

Flushing the Cooling System

Flush the internal water passages of the outboard with fresh water after each

use in salt, polluted, or muddy water. This will help prevent a buildup of

deposits from clogging the internal water passages.

NOTE: The engine can be stopped, or running at idle speed in neutral, when

flushing the cooling system. Do not flush the engine using a water source that

exceeds 310 kPa (45 psi).

1. Unscrew the cover from the end of the hose adapter.
2. Attach a water hose to the hose adapter.
3. Turn on the water and flush the cooling system for a minimum of three

minutes.

IMPORTANT: Do not run engine above idle speed when flushing.

4. Turn off the water and remove the water hose from the hose adapter.

Install the cover into the hose adapter.

a -

Hose adapter

b -

Sealing washer

c -

Cover

Top Cowl Removal and Installation

REMOVAL

1. Unlock the rear latch by pushing lever up.

22703

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 87 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: