Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 58

Страница: 58 / 159

Mercury Racing 2‑Stroke Oil is recommended for OptiMax engines that are

used in applications of extreme loads associated with commercial, work, or

extended periods of high RPM. The added lubrication and protection properties

with Mercury Racing 2‑Stroke oil, maximizes engine horsepower while

protecting against heat, reduces wear and carbon deposit build‑up.

Filling Oil Injection System

1. Place the outboard in a vertical operating position.
2. Remove the cowl cover.
3. Remove the oil filler cap.

a -

Cowl cover

b -

Oil filler cap

4. Oil filler caps with a dipstick ‑ Check the oil level on the dipstick. The first

set of holes indicates 0.94 liters (1 US qt) low. The second set of holes

indicates 1.89 liters (2 US qt) low. The third set of holes indicates

2.83 liters (3 US qt) low.

a -

Add 0.94 liters (1 US qt)

b -

Add 1.89 liters (2 US qt)

c -

Add 2.83 liters (3 US qt)

37147

37143

FUEL AND OIL

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 58 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: