Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 55

Страница: 55 / 159

WARNING

Fuel leakage is a fire or explosion hazard, which can cause serious injury or

death. Periodically inspect all fuel system components for leaks, softening,

hardening, swelling, or corrosion, particularly after storage. Any sign of

leakage or deterioration requires replacement before further engine

operation.

Because of possible adverse effects of alcohol in gasoline, it is recommended

that only alcohol‑free gasoline be used where possible. If only fuel containing

alcohol is available, or if the presence of alcohol is unknown, increased

inspection frequency for leaks and abnormalities is required.
IMPORTANT: When operating a Mercury Marine engine on gasoline containing

alcohol, storage of gasoline in the fuel tank for long periods should be avoided.

Long periods of storage, common to boats, create unique problems. In cars,

alcohol‑blend fuels normally are consumed before they can absorb enough

moisture to cause trouble, but boats often sit idle long enough for phase

separation to take place. In addition, internal corrosion may take place during

storage if alcohol has washed protective oil films from internal components.

Fuel Requirements

Do not use premixed gas and oil in this engine. The engine automatically

receives extra oil during engine break‑in. Use a fresh supply of the

recommended gasoline during engine break‑in and after engine break‑in.

Fuel Additives

To minimize carbon deposit buildup in the engine, it is recommended to add

Mercury or Quicksilver Quickstor fuel stabilizer additive to the engine's fuel at

each tank fill throughout the boating season. Use additive as directed on

container.

Avoiding Fuel Flow Restriction

IMPORTANT: Adding components to the fuel supply system (filters, valves,

fittings, etc.) may restrict the fuel flow. This may cause engine stalling at low

speed, and/or a lean fuel condition at high RPM that could cause engine

damage.

Low Permeation Fuel Hose Requirement

Required for outboards manufactured for sale, sold, or offered for sale in the

United States.

•

The Environmental Protection Agency (EPA) requires that any outboard

manufactured after January 1, 2009, must use low permeation fuel hose

for the primary fuel hose connecting the fuel tank to the outboard.

•

Low permeation hose is USCG Type B1‑15 or Type A1‑15, defined as not

exceeding 15/gm²/24 h with CE 10 fuel at 23 °C as specified in SAE J

1527 ‑ marine fuel hose.

FUEL AND OIL

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 55 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: