Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 104

Страница: 104 / 159

c. If an adjustment is necessary, do not pry or apply any force on the

center electrode. This is critical with any type of spark plug that has a

wear surface, such as platinum or iridium added to either the ground

electrode or the center electrode.

d. When it is necessary to widen the gap, use a tool that only pulls back

on the ground electrode without touching the center electrode, the

porcelain, or the wear portion of the ground electrode.

e. When it is necessary to close the gap, gently tap the plug ground

electrode on a hard surface.

4. Before installing spark plugs, clean off any dirt on the spark plug seats.

Install the plugs finger‑tight and then tighten an additional 1/4 turn or

tighten to the specified torque.

Description

lb‑in.

lb‑ft

Spark plug

–

Compressor Air Intake Filter

The filter should be changed every 100 hours of operation, or once a season.
IMPORTANT: Never run the engine without the air filter.

REMOVAL

1. Remove the three screws and filter cover from the engine.
2. Remove the filter from the cover.

a -

Cover

b -

Filter

INSTALLATION

1. Install the filter into cover.
2. Fasten the filter cover with three screws.

29476

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 104 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: