manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 23 / 159

Поделиться
Скачать
Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 23

As the outboard engine owner, you should, however, be aware that Mercury

Marine may deny you warranty coverage if your outboard engine or a part has

failed due to abuse, neglect, improper maintenance, or unapproved

modifications.
You are responsible for presenting your outboard to a Mercury dealer

authorized to service the product as soon as a problem exists. The warranty

repairs will be completed in a reasonable amount of time, not to exceed 30

days.
If you have any questions regarding your warranty rights and responsibilities,

you should contact Mercury Marine at 1‑920‑929‑5040.

Emission Certification Star Label

Outboards are labeled on the cowl with one of the following star labels.

The symbol for a cleaner marine engine means:
Cleaner air and water 

‑

 for a healthier lifestyle and environment.

Better fuel economy 

‑

 burns up to 30–40 percent less gas and oil than

conventional carbureted two‑stroke engines, saving money and resources.

Longer emission warranty 

‑

 protects consumer for worry‑free operation.

22531

One Star 

‑

 Low Emission

The One Star label identifies engines that meet

the Air Resources Board's 2001 exhaust

emissions standards. Engines meeting these

standards have 75% lower emissions than

conventional carbureted two‑stroke engines.

These engines are equivalent to the U.S. EPA's

2006 standards for marine engines.

42537

Two Stars 

‑

 Very Low Emission

The Two Star label identifies engines that meet

the Air Resources Board's Personal Watercraft

and Outboard marine engine 2004 exhaust

emissions standards. Engines meeting these

standards have 20% lower emissions than One

Star ‑ Low Emission engines.

42538

Three Stars 

‑

 Ultra Low Emission

The Three Star label identifies engines that meet

the Air Resources Board's Personal Watercraft

and Outboard marine engine 2008 exhaust

emissions standards or the Sterndrive and

Inboard marine engine 2003‑2008 exhaust

emission standards. Engines meeting these

standards have 65% lower emissions than One

Star ‑ Low Emission engines.

WARRANTY INFORMATION

eng

13

  

Содержание 115 Pro XS FourStroke
































































































































































Отзывы:

Нет отзывов