Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 156

Страница: 156 / 159

Oil Injection Set‑Up

FILLING OIL INJECTION SYSTEM

1. Fill the oil tank with the specified oil. Refer to

Filling Oil Injection

System.

Add only enough oil to bring the oil level up to the bottom of the

fill neck.

29465

All Models

Capacity

Fluid Type

Oil tank

4.72 liters (5 US qt)

OptiMax/DFI 2‑Cycle Engine Oil

PRIMING THE OIL INJECTION PUMP

Before starting engine for the first time, prime the oil injection pump. Priming

will remove any air that may be in the pump, oil supply hose, or internal

passages.

a -

Oil injection pump

b -

Oil supply hose

IMPORTANT: Fill the engine fuel system with fuel before priming the oil

injection pump. Otherwise, the fuel pump will run without fuel during the priming

process and may be damaged.
Prime the oil injection pump as follows:

1. Fill the engine fuel tank with fuel.

7912

OUTBOARD INSTALLATION

146

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 156 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: