Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 147

Страница: 147 / 159

A decal advising against using deep cycle batteries and wing nuts should be

placed on or near the battery box for future service reference. One 5/16 in. and

one 3/8 in. hex nut is supplied per battery for wing nut replacement. Metric hex

nuts are not supplied.

54395

Place decal on or near battery box for future

service reference. Included with the engine

rigging components are 5/16" and 3/8” hex

nuts to be used for battery terminal wing nut

replacement. Metric hex nuts must be obtained

locally.

8M0085862

Refer to the outboard owner’s manual for

battery requirements.

Battery cable size and length is critical.

Refer to engine installation manual for

size

requirements.

NOTICE

IMPORTANT:

DO NOT USE DEEP CYCLE BATTERIES!

13.5Nm (120 lb-in.)

DO NOT

USE

WINGNUTS

BATTERY CABLE CONNECTIONS

Single Outboard

a -

Red sleeve ‑ positive

(+)

b -

Black sleeve ‑

negative (–)

c -

Cranking battery

(+)

(-)

15496

OUTBOARD INSTALLATION

eng

137

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 147 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: