Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 159

Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 17

For additional information regarding events and circumstances covered by this

warranty, and those that are not, see the Warranty Coverage section of the

Operation and Maintenance Manual, incorporated by reference into this

warranty.

DISCLAIMERS AND LIMITATIONS:

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A  PARTICULAR  PURPOSE  ARE  EXPRESSLY  DISCLAIMED.  TO  THE
EXTENT  THAT  THEY  CANNOT  BE  DISCLAIMED,  THE  IMPLIED
WARRANTIES  ARE  LIMITED  IN  DURATION  TO  THE  LIFE  OF  THE
EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES
ARE  EXCLUDED  FROM  COVERAGE  UNDER  THIS  WARRANTY.  SOME
STATES/COUNTRIES  DO  NOT  ALLOW  FOR  THE  DISCLAIMERS,
LIMITATIONS  AND  EXCLUSIONS  IDENTIFIED  ABOVE,  AS  A  RESULT,
THEY  MAY  NOT  APPLY  TO  YOU.  THIS  WARRANTY  GIVES  YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL
RIGHTS  WHICH  VARY  FROM  STATE  TO  STATE  AND  COUNTRY  TO
COUNTRY.

Warranty Coverage and Exclusions

The purpose of this section is to help eliminate some of the more common

misunderstandings regarding warranty coverage. The following information

explains some of the types of services that are not covered by warranty. The

provisions set forth following have been incorporated by reference into the

Three Year Limited Warranty Against Corrosion Failure, the International

Limited Outboard Warranty, and the United States and Canada Limited

Outboard Warranty.
Keep in mind that warranty covers repairs that are needed within the warranty

period because of defects in material and workmanship. Installation errors,

accidents, normal wear, and a variety of other causes that affect the product

are not covered.
Warranty is limited to defects in material or workmanship, but only when the

consumer sale is made in the country to which distribution is authorized by us.
Should you have any questions concerning warranty coverage, contact your

authorized dealer. They will be pleased to answer any questions that you may

have.

GENERAL EXCLUSIONS FROM WARRANTY

1. Minor adjustments and tune‑ups, including checking, cleaning, or

adjusting spark plugs, ignition components, carburetor settings, filters,

belts, controls, and checking lubrication made in connection with normal

services.

2. Factory installed jet drive units ‑ Specific parts excluded from the warranty

are: the jet drive impeller and jet drive liner damaged by impact or wear,

and water damaged driveshaft bearings as a result of improper

maintenance.

WARRANTY INFORMATION

eng

7

«
...
15
16
17
18
19
...
»

Содержание 115 Pro XS FourStroke
































































































































































Отзывы:

Нет отзывов