Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 103

Страница: 103 / 159

1. Remove the spark plug leads by twisting the rubber boots while pulling

them off the spark plugs.

26899

2. Remove the spark plugs. Replace the spark plug if the electrode is worn;

the insulator is rough, cracked, broken, or blistered; or if the precious

metal is not visible on the spark plug electrode.

IMPORTANT: The color of the plug may not accurately reflect its condition. To

accurately diagnose a faulty plug, inspect the precious metal on the plug's

electrode. If no precious metal is visible, replace the plug.

a -

Precious metal

3. Set the spark plug gap. Refer to

Specifications

27848

a. All of the spark plugs should have the gap checked and corrected as

necessary before installation.

b. Measure the gap with a feeler gauge or pin gauge. Never use a

wedge‑type gap checking tool to inspect or to adjust the gap.

9381

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 103 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: