manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 85 / 159

Поделиться
Скачать
Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 85

Description

Nm

lb‑in.

lb‑ft

Outboard mounting locknuts and

bolts – standard boat transom

75

–

55

Outboard mounting locknuts and

bolts – metal lift plates and setback

brackets

122

–

90

•

Check the propeller blades for damage.

•

Inspect all hoses, clamps, fittings, tubing, sealing gaskets, and mounting

hardware for wear.

AFTER EACH SALTWATER OR POLLUTED WATER USE

•

Flush all internal passages with fresh water.

•

Wash the power package exterior (cowl, midsection, and gearcase) with

fresh water.

•

Flush the propeller and gearcase exhaust outlet with fresh water.

•

Remove the cowl and wipe off any saltwater spray with a damp cloth.

EVERY 25 HOURS OR EVERY 30 DAYS OF SALTWATER OR

POLLUTED WATER USE

•

Spray the powerhead and all external, unpainted metal surfaces (except

anodes) with Corrosion Guard.

Tube Ref

No.

Description

Where Used

Part No.

120

Corrosion Guard

Powerhead and all external, unpainted

metal surfaces (except anodes)

92-802878 55

EVERY 25 HOURS OR EVERY 30 DAYS, WHICHEVER OCCURS FIRST

•

Verify that the front and side cowl latches are tight. Tighten them if

necessary.

•

Inspect the fuel and oil systems for deterioration or leaks.

•

Inspect the hydraulic steering hoses for deterioration or leaks.

•

Inspect the steering link rod fasteners for wear. Lubricate all of the

specified components. Check all attachment hardware to ensure proper

torque.

•

Check the level and condition of the gearcase lubricant.

•

Check the alternator belt tension.

EVERY 50 HOURS OR ONCE A YEAR, WHICHEVER OCCURS FIRST

•

Lubricate all of the lubrication points listed in the manual.

•

Lubricate the splines on the driveshaft.

1.

•

Lubricate the length of driveshaft with Extreme Grease.

1.

These items should be serviced by an authorized dealer.

MAINTENANCE

eng

75

  

Содержание 115 Pro XS FourStroke
































































































































































Отзывы:

Нет отзывов