Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 8

Страница: 8 / 159

Fuel and Oil

Fuel Recommendations.................................................................................... 44

Fuel Requirements........................................................................................... 45

Fuel Additives................................................................................................... 45

Avoiding Fuel Flow Restriction......................................................................... 45

Low Permeation Fuel Hose Requirement ........................................................ 45

EPA Pressurized Portable Fuel Tank Requirements........................................ 46

Fuel Demand Valve (FDV) Requirement.......................................................... 46

Mercury Marine's Pressurized Portable Fuel Tank........................................... 46

Oil Recommendation........................................................................................ 47

Filling Oil Injection System................................................................................48

Filling Fuel Tank............................................................................................... 50

Features and Controls

Remote Control Features................................................................................. 51

Warning System............................................................................................... 51

Power Trim and Tilt...........................................................................................53

Trim Tab Adjustment........................................................................................ 57

Operation

Important Information........................................................................................58

Prestarting Check List.......................................................................................59

Operating in Freezing Temperatures................................................................ 59

Operating in Saltwater or Polluted Water......................................................... 59

Operating at High Elevations............................................................................ 60

Setting Trim Angle While Running Engine at Idle Speed................................. 60

Engine Break‑in................................................................................................ 60

Starting the Engine........................................................................................... 61

Gear Shifting..................................................................................................... 63

Stopping the Engine......................................................................................... 64

Jet Drive Operation........................................................................................... 64

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 8 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: