Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 159

Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 22

DISCLAIMERS AND LIMITATIONS

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A  PARTICULAR  PURPOSE  ARE  EXPRESSLY  DISCLAIMED.  TO  THE
EXTENT  THAT  THEY  CANNOT  BE  DISCLAIMED,  THE  IMPLIED
WARRANTIES  ARE  LIMITED  IN  DURATION  TO  THE  LIFE  OF  THE
EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES
ARE  EXCLUDED  FROM  COVERAGE  UNDER  THIS  WARRANTY.  SOME
STATES/COUNTRIES  DO  NOT  ALLOW  FOR  THE  DISCLAIMERS,
LIMITATIONS  AND  EXCLUSIONS  IDENTIFIED  ABOVE,  AS  A  RESULT,
THEY  MAY  NOT  APPLY  TO  YOU.  THIS  WARRANTY  GIVES  YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL
RIGHTS  WHICH  VARY  FROM  STATE  TO  STATE  AND  COUNTRY  TO
COUNTRY.

If you have any questions regarding your warranty rights and responsibilities,

you should contact Mercury Marine at 1‑920‑929‑5040.

California Air Resources Board Explanation of Your California

Emission Control Warranty Statement

YOUR WARRANTY RIGHTS AND OBLIGATIONS:

The California Air

Resources Board is pleased to explain the emission control system warranty on

your 2014–2015 model year outboard engine. In California, new outboard

engines must be designed, built, and equipped to meet the State's stringent

anti‑smog standards. Mercury Marine must warrant the emission control

system on your outboard engine for the periods of time listed below, provided

there has been no abuse, neglect, or improper maintenance of your outboard

engine.
Your emission control system may include parts such as the carburetor or fuel

injection system, the ignition system, and catalytic converter. Also included may

be hoses, belts, connectors, and other emission‑related assemblies.
Where a warrantable condition exists, Mercury Marine will repair your outboard

engine at no cost to you, including diagnosis, parts, and labor.

MANUFACTURER'S WARRANTY COVERAGE:

Select emission control parts

from model year 2001 and later outboard engines are warranted for four (4)

years, or for 250 hours of use, whichever first occurs. However, warranty

coverage based on the hourly period is only permitted for outboard engines and

personal watercraft equipped with hour meters as defined in s 2441(a)(13) or

their equivalent. If any emission‑related part on your engine is defective under

warranty, the part will be repaired or replaced by Mercury Marine.

OWNER'S WARRANTY RESPONSIBILITIES:

As the outboard engine owner,

you are responsible for the performance of the required maintenance listed in

the

Maintenance

section. Mercury Marine recommends that you retain all

receipts covering maintenance on your outboard engine, but Mercury Marine

cannot deny warranty solely for the lack of receipts or your failure to ensure the

performance of all scheduled maintenance.

WARRANTY INFORMATION

12

eng

«
...
20
21
22
23
24
...
»

Содержание 115 Pro XS FourStroke
































































































































































Отзывы:

Нет отзывов