Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 74

Страница: 74 / 159

•

When shifting, always stop at neutral position and allow the engine speed

to return to idle.

•

Always shift the outboard into gear with a quick motion.

•

After shifting the outboard into gear, advance the lever further to increase

speed.

27237

Stopping the Engine

Reduce the engine speed and shift the outboard to neutral position. Turn the

ignition key to "OFF" position.

26843

Jet Drive Operation

PRESTARTING CHECK LIST

Operator knows safe navigation, boating, and operating procedures.
An approved personal flotation device of suitable size for each person

aboard and readily accessible (it is the law).
A ring type life buoy or buoyant cushion designed to be thrown to a

person in the water.
Know your boats maximum load capacity. Look at the boat capacity plate.
Fuel supply OK.
Oil supply (oil injection) OK.
Ensure the boat drain plug is installed.
Arrange passengers and load in the boat so the weight is distributed

evenly and everyone is seated in a proper seat.
Tell someone where you are going and when you expect to return.

OPERATION

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 74 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: