MerCruiser Axius 350 Скачать руководство пользователя страница 136

Страница: 136 / 149

Section 6 - Storage

Page 128

90-8M0053363

eng

NOVEMBER 2010

1. Insert a small wire repeatedly to make sure that vent holes, water drain holes, and passages are unobstructed and open.

Sterndrive Water Drain Holes

a -

Speedometer pitot tube

b -

Trim tab cavity vent hole

c -

Trim tab cavity drain passage

d -

Gear housing water drain hole (1 each ‑ port and starboard)

e -

Gear housing cavity vent hole

f -

Gear housing cavity drain hole

NOTICE

The universal joint bellows may develop a set when stored in a raised or up position, causing the bellows to fail when returned

to service and allowing water to enter the boat. Store the sterndrive in the full down position.

2. Lower the sterndrive unit to the full down/in position.
3. For additional assurance against freezing and rust, after draining, fill the cooling system with propylene glycol mixed to the

manufacturer's recommendation to protect engine to the lowest temperature to which it will be exposed during freezing

temperatures or extended storage

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the manufacturers instructions, be used

in the seawater section of the cooling system for freezing temperatures or extended storage. Make sure that the propylene

glycol antifreeze contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow the propylene

glycol manufacturer's recommendations.

Battery Storage

Whenever the battery will be stored for an extended period of time, be sure the cells are full of water and the battery is fully charged

and in good operating condition. It should be clean and free of leaks. Follow the battery manufacturer's instructions for storage.

Recommissioning the Power Package

1. Ensure that all cooling system hoses are connected properly and hose clamps are tight.

CAUTION

Disconnecting or connecting the battery cables in the incorrect order can cause injury from electrical shock or can damage the

electrical system. Always disconnect the negative (‑) battery cable first and connect it last.

2. Install a fully charged battery. Clean the battery cable clamps and terminals and reconnect cables. Tighten each cable clamp

securely when connecting.

3. Coat the terminal connections with a battery terminal anti‑corrosion agent.
4. Perform all the checks in the before starting column of the

Operation Chart

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will overheat and suffer damage. Provide

a sufficient supply of water to the water inlets during operation.

5. Start the engine and closely observe instrumentation to ensure that all systems are functioning correctly.

6146

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды