MerCruiser Axius 350 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 149

background image

Section 5 - Maintenance

90-8M0053363

eng

NOVEMBER 2010

Page 111

NOTE: Engines with the sterndrive water inlet blocked off at the gimbal housing: Refer to Alternative Water Pickups.

!

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed. Before

installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from

starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

IMPORTANT: Do not allow the engine to pull air or seawater from alternative water pickup sources during the flushing procedure.

If equipped, ensure that all alternative water inlet hoses are plugged at both ends.
1. Remove the boat from the water.
2. Close the seacock, if equipped.

For visual clarity, the secock shown is not installed

a -

Hose fitting to engine

b -

Seacock

c -

Handle (closed position)

d -

To water source pickup attachment

3. If equipped with an alternative water pickup and not equipped with a seacock, disconnect the water hose from the alternative

water pickup and plug both ends, excluding the Bravo sterndrive.

4. Ensure that the inlet water hose from the sterndrive to the engine is connected.
5. Remove the quick‑connect fitting from the parts bag supplied with the engine.
6. Attach the quick‑connect fitting to a water hose.

a -

Quick connect fitting (water hose end)

b -

Water hose

7. Snap the quick‑connect fitting with the water hose into the flush socket on the engine.

a -

Water hose

b -

Quick‑connect fitting (water hose end)

c -

Flush socket

a

c

b

d

18510

18487

a

b

a

b

c

18489

«
...
117
118
119
120
121
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: Vanguard Страницы: 20

Бренд: E-Z-GO Страницы: 100

Бренд: Briggs & Stratton Страницы: 102

Бренд: vario helicopter Страницы: 4

Бренд: Doosan Страницы: 350

Бренд: ACM Страницы: 36

Compact CA Series

Бренд: Hägglunds Страницы: 45

Бренд: Yaroslavl Engine Plant Страницы: 168

Бренд: Himax Страницы: 2

GARDEN SNOWBUSTER (160F)

Бренд: Texas Страницы: 33

Бренд: Toyota Страницы: 525

Бренд: Volvo Страницы: 64

Concept engines

Бренд: RB Страницы: 19

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Stiga Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды