MerCruiser Axius 350 Скачать руководство пользователя страница 32

Страница: 32 / 149

Section 2 - Getting to Know Your Power Package

Page 24

90-8M0053363

eng

NOVEMBER 2010

Bravo Sterndrive Serial Number and Identification

The Bravo sterndrive serial number, gear ratio, model number, and bar code are embedded in the ground plate on the port side

of the sterndrive.

33533

Bravo sterndrive information on ground plate

The serial number is also stamped as a permanent reference on the sterndrive casting inside the back cover.

33534

Bravo sterndrive serial number stamping

Electronic Helm Steering

The electronic helm steering operates through electronic signals. A computer‑controlled electric motor simulates the resistance

feedback found in hydraulic steering systems.
We recommend that you drive carefully until you have a chance to explore the Axius system's handling characteristics and boat's

responses in an open area clear of obstructions or other boat traffic. The initial steering setting of two turns lock‑to‑lock provids a

fast steering response. Maneuvers at speed can be more abrupt than expected. The distributor can adjust the number of turns, if

desired.

Dual‑Handle Electronic Remote Control (ERC) with DTS Trackpad Features and Operation

Operation

The electronic remote control (ERC) handle operates the shift and throttle. Push the ERC handles handle forward from neutral to

the first detent for forward gear. Continue pushing the ERC handle forward to increase speed. Pull the ERC handle from the

forward position to the neutral position to decrease speed and eventually stop. Pull the ERC handle back from neutral to the first

detent for reverse gear. Continue pulling the handle back to increase speed.

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды