MerCruiser Axius 350 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 149

background image

Section 5 - Maintenance

Page 96

90-8M0053363

eng

NOVEMBER 2010

Water‑Separating Fuel Filter (MPI)

Water‑Separating Fuel Filter

!

WARNING

Fuel is flammable and explosive. Ensure that the key switch is off and the lanyard is positioned so that the engine cannot start.

Do not smoke or allow sources of spark or open flame in the area while servicing. Keep the work area well ventilated and avoid

prolonged exposure to vapors. Always check for leaks before attempting to start the engine, and wipe up any spilled fuel

immediately.

!

CAUTION

Failure to release pressure from the fuel system will result in fuel spraying out, which can cause a fire or explosion. Allow the

engine to cool completely and release all fuel pressure before servicing any part of the fuel system. Always protect eyes and

skin from pressurized fuel and vapors.

GEN III Models

a -

Cool Fuel Module

b -

Cool Fuel Module harness

c -

Filter cap

d -

Filter assembly retaining screw

e -

Fuel filter element

f -

Filter cup

g -

Cool Fuel Module filter reservoir

h -

O‑ring

Removal

1. Allow the engine to cool down.

NOTE: Mercury MerCruiser recommends that the engine be shut off for 12 hours prior to filter removal.

2. Close fuel supply valve, if equipped.
3. Disconnect the Cool Fuel Module harness from the engine wiring harness.
4. Turn the key switch to the start position and allow the starter to operate for 5 seconds.
5. Turn key switch to off position.
6. Loosen each filter assembly retaining screw until the screw is disengaged from the Cool Fuel Module. Do not remove the filter

assembly retaining screws from the filter cap.

7. Unseat the filter assembly by grasping the filter assembly handle and pulling upward. Do not remove the filter assembly from

the Cool Fuel Module at this time.

8. Allow any fuel that may be in the filter assembly to drain out through the bottom of the filter assembly and into the Cool Fuel

Module filter reservoir.

d

a

b

c

e

f

g

h

8837

«
...
102
103
104
105
106
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: Toyama Страницы: 44

Бренд: Superrollo Страницы: 68

Бренд: Volvo Penta Страницы: 90

Бренд: Volvo Penta Страницы: 108

Бренд: Volvo Penta Страницы: 41

Бренд: Lycoming Страницы: 194

Бренд: RIB Страницы: 44

Бренд: Quectel Страницы: 39

Бренд: Front Runner Страницы: 15

Бренд: HIOTH TECHNOLOGY Страницы: 5

Бренд: O.S. Speed Страницы: 4

Бренд: LONCIN Страницы: 44

SATURNO BIALBERO 350

Бренд: Gilera Страницы: 140

Бренд: Wood-mizer Страницы: 80

Бренд: Iveco Страницы: 74

Бренд: Paccar Страницы: 111

Бренд: Nakayama Страницы: 43

Бренд: Hirth Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды