MerCruiser Axius 350 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 149

background image

Section 5 - Maintenance

90-8M0053363

eng

NOVEMBER 2010

Page 95

2.

a -

PCV valve

b -

Hose

3. If inspecting the valve with the engine stopped:

a. Disconnect the PCV valve from the hose.
b. Shake the PCV valve. If you hear a metallic rattle, the valve is functional. If you do not hear the rattle, replace the valve.
c. Install the valve onto the hose.

4. If inspecting the valve with the engine running:

a. Leave the hose connected to the PCV valve.
b. Start the engine. You may hear the sound of suction through the PCV valve.
c. Place a small sheet of card stock or heavy paper near the open end of the PCV valve. If the valve is working, the manifold

vacuum will suck the paper against the open end of the valve.

d. Stop the engine. If the paper was not drawn onto the open end of the valve, check the hose connection and for vacuum

leaks in the hose. If no leaks are present, replace the PCV valve.

5. Install the PCV valve in the valve cover and reconnect the hose, if not connected already.
6. Ensure that the PCV valve is tightly seated in the valve cover.

Replacement

IMPORTANT: Use only Mercury MerCruiser replacement parts to ensure compliance with emission regulations.
1. Remove the PCV valve from the port valve cover.

a -

PCV valve

b -

Hose

2. Disconnect the PCV valve from the hose and discard the valve.
3. Install a new PCV valve in the valve cover and reconnect the hose.
4. Ensure that the PCV valve is tightly seated in the valve cover.

mc71925-1

a

b

mc71925-1

a

b

«
...
101
102
103
104
105
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: E-Z-GO Страницы: 100

Бренд: Scania Страницы: 83

Бренд: Yaroslavl Engine Plant Страницы: 168

Бренд: Daewoo Страницы: 188

Бренд: Leadshine Страницы: 18

Бренд: Yanmar Страницы: 240

Stagemaker SM10

Бренд: R & M Страницы: 71

Бренд: Mitsubishi Страницы: 79

Бренд: Volvo Penta Страницы: 176

Бренд: Toyota Страницы: 599

P10-70-SSC Series

Бренд: LinMot Страницы: 32

Бренд: LinMot Страницы: 32

SENSORLESS-BLDC-MOTOR-RD

Бренд: Silicon Laboratories Страницы: 12

Бренд: CAB Страницы: 14

Бренд: A'OK Страницы: 6

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 3

Бренд: Rotax Страницы: 102

Бренд: Rotax Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды