MerCruiser Axius 350 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 149

background image

Section 5 - Maintenance

Page 112

90-8M0053363

eng

NOVEMBER 2010

8. Open the water source of the water hose to a full flow.
9. Allow the water to flush the sterndrive for 30 seconds.
10. Place the remote control in neutral idle speed position and start engine.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will overheat and suffer damage. Provide

a sufficient supply of water to the water inlets during operation.

11. Operate the engine at idle speed in neutral gear. Do not exceed 1200 RPM.
12. Monitor the engine temperature while operating the engine.
13. Flush the engine for 5 to 10 minutes or until discharge water is clear.
14. Shut off the engine.
15. Allow the water to flush the sterndrive for 10 seconds.
16. Turn off the water source.
17. Disconnect the quick‑connect fitting and water hose from the flush socket on the engine by pressing the release button on

the flush socket.

a -

Quick‑connect fitting (water hose end)

b -

Flush socket release button

18. Remove the quick‑connect fitting from the water hose.

a -

Quick‑connect fitting (water hose end)

b -

Water hose

19. Retain the quick‑connect fitting with the water hose end for repeated use by storing it separately in a storage compartment

on the boat for easy access.

IMPORTANT: Do not store the quick‑connect fitting in the flush socket on the engine. Doing so would allow the seawater

pump to suck air during engine operation causing an overheating problem. Damages due to engine overheating are not

covered by Mercury MerCruiser Warranty.

Quick-connect fitting stored in the boat

a -

Quick‑connect fitting (water hose end)

b

a

18488

18487

a

b

25900

a

«
...
118
119
120
121
122
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: DLA Страницы: 7

90000 I/C 525 Series

Бренд: Briggs & Stratton Страницы: 16

Бренд: Mile HaoXianG Model Technology Страницы: 3

Бренд: Yanmar Страницы: 52

Бренд: Key Automation Страницы: 44

Бренд: IMS Страницы: 6

Бренд: dunkermotoren Страницы: 30

Бренд: VM Страницы: 108

Бренд: Winterthur Gas Страницы: 495

Бренд: RIB Страницы: 44

Бренд: Quectel Страницы: 39

Бренд: Seva-tec Страницы: 20

Бренд: DANA Страницы: 4

Бренд: Ingersoll-Rand Страницы: 159

Бренд: TKM Страницы: 4

Бренд: Jacobsen Страницы: 104

Бренд: IAME Страницы: 28

Бренд: Mitsubishi Страницы: 155

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды