MerCruiser Axius 350 Скачать руководство пользователя страница 79

Страница: 79 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 71

4. A horn beep sounds on VesselView and the green circle icon on the Axius Premier screen will display "TRACK." The "TRACK"

icon on the VesselView screen should illuminate.

31411

Waypoint Sequence TRACK icon

5. If you are in a waypoint arrival zone set by the chart plotter, Waypoint Sequence mode only informs Axius Premier it is OK to

proceed to next waypoint. Waypoint Sequence mode acts as a waypoint acknowledge function and Axius Premier sounds a

horn beep when in the zone.

WARNING

In some Precision Pilot modes—"Auto Heading," "Track Waypoint," and "Waypoint Sequence"—the boat navigates a preset

course. The boat does not automatically respond to hazards such as other watercraft, obstacles, swimmers, or underwater

terrain. Collision with these hazards could cause boat damage, serious injury, or death. The operator must stay at the helm,

ready to evade hazards and warn others of course changes.

6. Press the enter button to acknowledge it is OK to turn. The enter button is in the upper right corner of VesselView and has a

check mark symbol. Once acknowledged, Axius Premier Trackpad tracks to the next waypoint in the route.

7. Stay alert; the boat turns automatically in this mode. The operator must know if it is safe to turn when the vessel is entering

a waypoint arrival zone. Inform passengers that the boat automatically turns so they can be prepared.

31414

Waypoint acknowledge screen

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды