MerCruiser Axius 350 Скачать руководство пользователя страница 55

Страница: 55 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 47

•

Accessing the slow‑speed trolling features of the integrated transmission system.

28090

Yacht handled ERC levers with DTS trackpad, Typical

Item Control

Function

"NEUTRAL" lights

Illuminate when the transmission is in the neutral gear position. The lights flash when the

engine is in throttle only mode.

Not used

None

"TRANSFER"

Allows boat control to be transferred to a different helm. Refer to Helm Transfer.

"DOCK"

Reduces throttle capacity to approximately 50% of normal throttle.

"THROTTLE ONLY"

Allows the boat operator to increase engine RPM for warm‑up without shifting the

transmission into gear.

"1 LEVER"

Enables the throttle and shift functions of both engines to be controlled by the port lever.

"SYNC"

Turns off or on the auto‑synchronization feature. Refer to Synchronizing Engines.

"+" (increase) and "–"

(decrease)

Increases and decreases settings for various functions, like cruise control speed.

NOTE: Not all functions may be active.

Dock

Dock mode reduces the RPM throughout the range by 50%. Dock mode also reduces available power when the joystick is enabled,

allowing finer control of engine power in close quarter situations.

31464

"DOCK" button

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды