MerCruiser Axius 350 Скачать руководство пользователя страница 70

Страница: 70 / 149

Section 3 - On The Water

Page 62

90-8M0053363

eng

NOVEMBER 2010

5. A safety popup (warning screen) appears on VesselView.

33920

Skyhook warning screen on VesselView

6. To acknowledge that you understand the warning on the screen and close the safety popup, press the enter button on

VesselView. The enter button is the button with the check mark on it.

7. When the Skyhook system engages, a one second solid horn beep sounds one time. The "SKYHOOK" button light stops

blinking and remains on once Skyhook is engaged.

8. The VesselView "SKYHOOK" screen displays a green circle with the word "ON" when Skyhook engages. See

The Skyhook

Screen in VesselView

information.

9. When Skyhook is engaged you must remain at the helm and maintain a vigilant watch. Disengage Skyhook if anyone enters

the water or approaches the boat from the water.

10. Press the "SKYHOOK" button a second time to put Axius Premier in standby. All lights other than "STANDBY" turn off.
11. To disengage Skyhook, you must choose one of the following methods:

•

Press the "SKYHOOK" button on the Axius Premier Trackpad.

•

Move any ERC lever out of neutral.

•

Move the joystick.

A single horn beep sounds when the feature disengages. See

Disengaging Skyhook

for complete details.

The Skyhook Screen in VesselView

In Skyhook mode VesselView displays a special Skyhook screen. The elements of the Skyhook screen are:
•

RPM of the engines.

•

The rotation angle of the boat icon shows the yaw of the boat relative to its position when Skyhook was first engaged.

•

The horizontal and vertical displacement of the vessel from the cross hairs is proportional to the position error reported by

the GPS.

•

Each gradation of color in the circular target on the VesselView screen is equivalent to 5 meters of error. If the boat exceeds

20 meters of error, then the boat is located at the edge of the circle. The boat continues to try to correct until Skyhook is

disengaged.

Skyhook screen on VesselView

a -

Location where Skyhook is set

b -

Location where boat is relative to set

location

c -

5 meter gradation

d -

Engine RPM

27716

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды