MerCruiser Axius 350 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 149

background image

Section 3 - On The Water

Page 48

90-8M0053363

eng

NOVEMBER 2010

To engage Dock mode:
1. Place both ERC levers in neutral.
2. Press the "DOCK" button located on the DTS Trackpad attached to the ERC levers.
3. The "DOCK" button light turns on.
4. Place either ERC lever into gear.
5. The engines raise the RPM at a proportionally lower RPM for the ERC lever position, and with half the usually available power.
To disengage Dock mode:

NOTE: Dock only disengages with the levers in a detent.

1. Bring both ERC levers to any detent.
2. Press the "DOCK" button. The "DOCK" button light turns off.

Throttle Only

31465

"THROTTLE ONLY" button

To engage Throttle Only mode:
1. Place both ERC levers in neutral.
2. Press the "THROTTLE ONLY" button, located on the DTS trackpad.
3. The "THROTTLE ONLY" button light illuminates and the neutral lights blink.
4. Place either ERC lever into gear.
5. The RPM of the engines can be increased, while the transmissions remains in Neutral.

NOTE: Pressing the "THROTTLE ONLY" button while the ERC levers are in gear, turns off the button light, but the boat remains

in throttle only mode until you place the levers in neutral.

To disengage throttle only mode:
1. Bring both ERC levers to neutral. Throttle only will not disengage unless the ERC levers are in neutral.
2. Press the "THROTTLE ONLY" button. The "THROTTLE ONLY" button light turns off.
3. The neutral lights remains on.

«
...
54
55
56
57
58
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: Daihatsu Страницы: 196

Бренд: Wacker Neuson Страницы: 114

Бренд: Econex Страницы: 14

Бренд: HOND Страницы: 48

Бренд: SSANGYONG Страницы: 16

Бренд: SSANGYONG Страницы: 42

Бренд: Chamberlain Страницы: 20

Бренд: Chamberlain Страницы: 28

Бренд: Wilesco Страницы: 4

Бренд: Yanmar Страницы: 240

Бренд: Powertrain Страницы: 36

Бренд: O.S. engine Страницы: 48

2.0-1120 - V1.1

Бренд: MVVS Страницы: 2

Бренд: MVVS Страницы: 6

Бренд: Briggs & Stratton Страницы: 16

Бренд: Briggs & Stratton Страницы: 6

Бренд: V2 Страницы: 16

Бренд: Desert Aircraft Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды