MerCruiser Axius 350 Скачать руководство пользователя страница 40

Страница: 40 / 149

Section 2 - Getting to Know Your Power Package

Page 32

90-8M0053363

eng

NOVEMBER 2010

•

Waypoint Sequence

—controls the boat on a pre‑determined path with multiple waypoints

a -

SkyHook

b -

Turn to starboard

c -

Waypoint Sequence

d -

Response

e -

Track Waypoint

f -

Auto Heading

g -

Resume

h -

Turn to port

The buttons on the Precision Pilot Trackpad have the following functions:

Function

Description

SkyHook

Engages and disengages SkyHook. Mode is only available when the joystick is centered, both engines are

running, GPS and Heading Sensors are available, and levers are in neutral.

Turn < and >

Each press of the button causes a 10 degree course change in the Auto Heading mode. (A tap port or starboard

on the joystick initiates a one degree change in course.)

Waypoint
Sequence

Engages Waypoint Sequence, driving the boat on a course set with multiple waypoints on the charplotter.

Waypoint Sequence is available when the "WAYPOINT SEQUENCE" button is pressed, a NMEA‑0183 stream

is available from a chart plotter, and the GPS and heading sensor signals are available. When in "WAYPOINT

SEQUENCE" mode, the joystick or "<" or ">" will cause the Precision Pilot to change to heading control and

change the heading 1°.

Response

Increases or decreases the amount of control exerted by the Precision Pilot on disturbances to external course

changes in three levels. Selection will be in a "(123‑321)" format. The response levels can be calibrated.

Track
Waypoint

Engages Precision Pilot in (GPS) Track mode. Track can be engaged by either pressing the track button or

pressing the auto button then the track button. Route Tracking is available when the "Track" button is pressed,

a NMEA‑0183 stream is available from a chart plotter, and the GPS and heading sensor signals are available.

When in "Track" mode, the joystick or "<" or ">" will cause the Precision Pilot to change to heading control and

change the heading 1°.

Auto Heading

Engages Auto Heading mode. Heading control is available when the "Auto Heading" button is pressed, and

GPS and IMU signals are available. (See "Turn < and >" for course adjustment information.)

Resume

Resumes previous Auto/Track Course.

NOTE: Moving the steering wheel will always take control of the boat. A slight detent will have to be overcome to give the operator

feedback that the they are taking control from the Precision Pilot. The "Resume" button will return the Precision Pilot to control in

the previous mode.

35301

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды