MerCruiser Axius 350 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 149

background image

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 49

1 (Single) Lever

The Axius system features the ability to command both engines with a single lever. This feature simplifies engine management

during rough sea conditions by allowing you to grasp a single lever to command both engines simultaneously.

31466

"1 LEVER" button

To engage 1 (single) lever mode:
1. Place both ERC levers in neutral.
2. Press the "1 LEVER" button located on the DTS Trackpad attached to the ERC levers.
3. The "1 LEVER" button lights.
4. Place the starboard ERC lever into gear.
5. The engine RPM raises and lowers simultaneously while the transmissions remain in the same gear.
To disengage 1 (single) lever mode:
1. Place both ERC levers in neutral.
2. Press the "1 LEVER" button. The "1 LEVER" button light turns off.

Sync

The Axius system features Sync, an automatic engine synchronization feature, which engages automatically at key‑up. Sync

monitors the position of both levers. If both levers are within 10% of one another, the port engine synchronizes to the starboard

engine's RPM. The smartcraft system will automatically disengage Sync at the last 10% of lever range to allow each engine the

ability to reach maximum available RPM. Sync cannot engage until its minimum RPM is met.
VesselView shows an orange icon if the engines exceed a 10% difference in RPM of each other, and the icon turns red when they

synchronize. The icon turns off when Sync is off.

31467

"SYNC" button

«
...
55
56
57
58
59
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: BAFANG Страницы: 4

Бренд: Man Страницы: 136

Бренд: Westerbeke Страницы: 140

Бренд: TOPMAQ Страницы: 17

Бренд: YASKAWA Страницы: 447

Бренд: Vimar Страницы: 16

Бренд: Lycoming Страницы: 84

Бренд: GSK Страницы: 24

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: LONCIN Страницы: 23

Бренд: V2 Страницы: 4

Бренд: Ford Страницы: 42

Бренд: Yanmar Страницы: 48

Бренд: BAFANG Страницы: 9

Бренд: Baldor Страницы: 4

Бренд: KaVo Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды