MerCruiser Axius 350 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 149

background image

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 53

7. If the ERC Handles are moved to neutral, Auto Heading turns off, a single beep sounds, and the "STANDBY" light turns on.

You cannot resume your course by pressing the "RESUME" button.

a -

"OFF" button

b -

Current heading

c -

Drive positions

d -

Engine RPM

Pressing the "AUTO HEADING" button causes VesselView to displays the "AUTO HEADING" screen for three seconds. If the

VesselView "AUTO HEADING" screen does not appear, the "AUTO HEADING" screen needs to be activated in VesselView

calibration. Axius CAN still engages whether the screen appears or not.

NOTE: If you press the "AUTO HEADING" button a second time, the Axius CAN goes to Standby mode and all lights other than

"STANDBY" turn off.

Disengage Auto Heading

1. Disengage the Auto Heading mode by any of the following actions:

•

Place the ERC levers for both engines in neutral.

•

Turn the steering wheel beyond the electronic detent.

•

Press the "AUTO HEADING" button on the Axius track pad. The "AUTO HEADING" button LED light turns off.

a -

Button LED light

b -

"AUTO HEADING" button

To Resume to a Heading

The "RESUME" button light turns on if the previous course heading is available to resume. The previous heading can only be

resumed within one minute of the Auto Heading being disengaged or if the boat has not turned more than 90°. You can adjust

these values during configuration.
If you disengage the Auto Heading by turning the steering wheel or if you press one of the "TURN" buttons with Auto Heading still

engaged, press the "RESUME" button to resume the previous heading.

Changing VesselView Mode Display Times

All modes display a screen on VesselView for three seconds by default. The length of time that a screen is visible in VesselView

can be changed from no display at all, display up to 10 seconds, or display the screen until changed.
To change the display time:
1. Open VesselView.
2. Select Setting.

31408

b

c

a

d

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

TURN

32510

a

b

«
...
59
60
61
62
63
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: Exalto Страницы: 28

Бренд: TAYO Страницы: 42

Бренд: MTU Страницы: 156

SIMOTICS SD 1LE8 Series

Бренд: Siemens Страницы: 29

SIMOTICS M-1PH1

Бренд: Siemens Страницы: 8

Simotics SD 1LE7

Бренд: Siemens Страницы: 44

SIMOTICS S-1FT2

Бренд: Siemens Страницы: 102

SIMOTICS T-1FW4407-1KM81-1BC0-Z

Бренд: Siemens Страницы: 114

SIMOTICS S-1FK7 DYA Generation 2

Бренд: Siemens Страницы: 104

SIMOTICS SD SH 71 315 Series

Бренд: Siemens Страницы: 132

SIMOTICS SD 1LE5

Бренд: Siemens Страницы: 136

SIMOTICS S-1FK7

Бренд: Siemens Страницы: 134

SIMOTICS M-1PH1

Бренд: Siemens Страницы: 134

Simotics M-1FE1 Series

Бренд: Siemens Страницы: 150

SIMOTICS S-1FG1

Бренд: Siemens Страницы: 170

SIMOTICS M-1FE2

Бренд: Siemens Страницы: 162

SIMOTICS M-1PH8

Бренд: Siemens Страницы: 186

SIMOTICS M-1FE2

Бренд: Siemens Страницы: 214

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды