Mendota FV46 Скачать руководство пользователя страница 86

Страница: 86 / 96

85-03-01108

FV46

Page

6.7

REPLACEMENT PARTS INFORMATION

How to Access Components

The descriptions below show where the main fireplaces components are located and how to access them for service. The

descriptions show how to access the components after the fireplace has been installed. All components are also accessible from

the outside of the unit before the fireplace is installed.

Pilot

: The pilot is in the center of the firebox between the burners.

Gas Valve

: The main gas valve is located on the left side of the firebox. An inspection panel is provided on the left firebox wall

that allows inspection of the gas valve, wiring, and gas inlet connections.

Complete Valve Assembly

To make working on components easier, this fireplace has been designed with the valve, pilot,

shutter boxes, shutter cables and gas lines as part of one assemble that can be removed from the fireplace. To remove the

assembly first remove the inspection panel. This will allow the main gas inlet and wires to the valve, rear burner solenoid and

pilot to be disconnected. After disconnecting the gas line and wires remove the screws from the valve mounting plate (13 on the

left side and two on the floor of the firebox). Then remove the entire assembly from the firebox.

Ignition Control Module

: The ignition control module is mounted on the left side in a protruding box beyond the main gas valve

(when accessing from inside the firebox). It is secured to the outer wall of the box with two screws. Access to the ignition control

module is available through the inspection panel. First remove the inspection panel. Then locate the ignition control module.

Convection Blowers

: The convection blowers are mounted on the firebox rear left and right sides. To access the convection

blowers, remove burner airbox, burners and the left and right-side blower access plates.

Accent Light

: The accent light is mounted in the firebox top center area. The accent light wire harness is run from the light

housing to the left side and then down to the ignition control module.
Please contact your Mendota Dealer for parts availability and parts pricing.

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды