Mendota FV46 Скачать руководство пользователя страница 35

Страница: 35 / 96

85-03-01108

FV46

Page

On fireplaces with electronic ignition system that come with a PF2 remote the convection fans function must be programed

out of the remote. This will ensure that the convection fans cannot be turned on. Follow the directions below to remove

the convection fans function from the remote.

Remove a battery from the remote.

Hold down both the ON/OFF key and MODE key and

reinstall the battery.

Continue to hold the ON/OFF key. Release the MODE

key. Press the MODE key once to highlight the

convection fan function.

While still holding the ON/OFF key press the DOWN

ARROW key. The display will change from “Set” to

“Clr” to indicate that the convection fan function has

been disabled.

Release the ON/OFF key.

3.2.18.3.1

Mendota Cool Wall

The Mendota Cool Wall system uses natural convection to take heat off the wall directly above the fireplace and redirects it up and

away from surrounding areas. Testing has shown that when using a Cool Wall system, temperatures above the fireplace are reduced

making it possible to mount a television 15” above the fireplace’s top air gap.

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды