Mendota FV46 Скачать руководство пользователя страница 56

Страница: 56 / 96

85-03-01108

FV46

Page

4.10

NATURAL GAS TO LPG CONVERSION

WARNING

This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s

instructions and all applicable codes and requirements of the authority having jurisdiction. If the information

in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result

causing property damage, personal injury or loss of life. The qualified service agency is responsible for the

proper installation of this kit. The installation is not proper and complete until the operation of the

converted appliance is checked as specified in the owner instructions supplied with the kit.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury.

General Conversion Information

Kit # HA-88-00080 for Mendota Model FV46

Caution: The electrical supply to the fireplace must be turned

off prior to performing the conversion. The gas supply must

be shut off prior to disconnecting the electrical power.

Orifice sizes requirement

A Natural Gas to LPG conversion kit #HA-88-00080 must be ordered and

installed to convert the FV-46 Fireplace to burn LPG.
LP Conversion Kit #HA-88-00080 contains the following parts: One

Motorized LP Pressure Regulator and two Cap Orifices drill #55 and drill

#1/16th.

Figure 4-9 HA-88-00080 LP Kit Parts

Burner Orifices

[#55]

Motorized

LP Pressure

Regulator

[10.0-5.5"WC]

Burner Orifices

th]

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды