manualshive.com logo in svg

Mendota FV46, Инструкция по установке и эксплуатации

Поделиться
Скачать
Mendota FV46 Скачать руководство пользователя страница 74

85-03-01108 

FV46 

Page 

74

 

5.4

 

Operating information 

 

Using Your Remote Control 

Your Mendota remote control is pre-programmed to your fireplace. Ensure you have installed 3 AAA batteries into your remote.  
Press the top button on the remote control. If you do not hear a beep when you press this button, follow the instructions below 

to synchronize your fireplace and remote control. 

 

Synchronizing the Fireplace and Remote Control 

Note:

 The master switch and sync switch are located on the bottom left corner of the 

fireplace in the left side air gap. 

Master Switch” 

The master switch acts as the main safety on/off control 

for the main gas burners only. When the master switch is in the off-

condition, the main gas burners will not turn on. However, all other 

fireplace functions, including the Continuous Pilot mode (CPI), will 

operate. When the master switch is in the on-condition, the main burners 

will function as designed. 

In case of an emergency, toggle the master switch to off to turn off the main burners. 
To synchronize the fireplace and remote control, follow the steps below: 

1. 

Toggle the 

master switch

 to “on” (toggle forward).

 

2. 

Locate 

sync switch

 (above master switch in the left-side air gap). Press the sync button and release. The fireplace will 

beep 

three

 

times

 indicating that it is ready to synchronize with a remote control. (Note: If you do not hear any beeps when you 

press the sync button, contact your Mendota dealer or installer for assistance.) 

3. 

Within seven seconds, press the “on” button on the remote control. The fireplace will 

beep four

 

times

 to indicate that the 

remote control’s command is accepted and sets to the particular code of that controller.   

Your system is now initialized.  

 

Figure 5-1 Sync Switch 

Содержание FV46

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды