manualshive.com logo in svg

Mendota FV46, Инструкция по установке и эксплуатации

Поделиться
Скачать
Mendota FV46 Скачать руководство пользователя страница 31

85-03-01108-C 

FV46 

Page 

31

 

 

FRAMING DEPTH and FINISHING GUIDES 

This fireplace comes with one standard finishing guide that will be used with any inside finish decorative front. Door installation 

will require the use of guides supplied with the door kit. Grace, Mission and Willowbrook fronts have optional finishing 

applications depending on what wall finishing material and what finished look you want to achieve. Refer to the 

Grace/Willowbrook/Mission front guide options. 
It is important to know what wall finish is being used and what finish option is preferred prior to unit installation when choosing 

a Grace, Willowbrook or Mission front. 
When the wall finish material will exceed 2 ½” in depth, the Recessed Mount guide kit will be required to allow the decorative 

front to install properly. 
All finish guides, standard or optional, protrude 1” from the face of the unit. Factory guides are installed with rivets and can be 

removed with a 

⅛

” drill bit. 

The finish guide used should be permanently left in place. 

 

GRACE/WILLOWBROOK/MISSION FRONT GUIDE OPTIONS 

This fireplace comes with guides to ensure finish materials do not encroach into the convection air area of the fireplace. Some 

decorative fronts for this fireplace come with additional guides for different finishing and appearance options. 

There are two options for finishing the fireplace when installing a Mission, Grace or Willowbrook front. One of two guide kits 

must be ordered. 

Please read the following instruction before installing the finishing material on the front of this fireplace. If you have any 

questions about finishing the fireplace, contact a Mendota dealer or the Mendota Service Department. 

•

 

To prevent damage, remove any decorative front, screen, or door from the fireplace and mask the fireplace 

glass frame prior to installation of finish materials 

 

Flush Mount Guide kit - Installing Front On Top Of Finishing Materials With The Screen Recessed 

Note:

 Order the Flush Mount Guide Kit from the pricing sheet. 

This option requires that your finish material be less than 3” thick including backing materials and reasonably flat. If they are 

not, use the Recessed Mount Guide Kit instead. 

 

 

 

Содержание FV46

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды