manualshive.com logo in svg

Mendota FV46, Инструкция по установке и эксплуатации

Поделиться
Скачать
Mendota FV46 Скачать руководство пользователя страница 18

85-03-01108-C 

FV46 

Page 

18

 

 

Normal Surface Temperatures 

WARNING:  The supplied barrier screen must be installed, always, when this fireplace is in operation. Do not 

place any object directly in front (within 60” from barrier screen surface) or directly above (on the front 

edge of the mantel). This is a heating appliance. Areas directly in front and above this appliance will be very 

hot and can damage most household objects if placed too close.  Keep Furniture pieces at least 60” away in 

front of the barrier screen surface. 

HINT: To greatly reduce surface temperatures surrounding this Fireplace during operation, Mendota 

recommends operating the integrated convection air blowers which aid in cooling all surrounding surfaces. 

Mendota Fireplaces comply with ANSI Z21.88-2017 Standards for maximum surface temperatures (ambient plus 117

o

F) on 

exposed “combustible” surfaces adjacent to the Fireplace. 
Be aware that surfaces in front of, above and adjacent to this heater appliance can be too hot to touch. As long as all required 

clearances to combustibles are met and the required finishing materials are used, this appliance will perform safely. Note that 

the exposed surfaces immediately surrounding the Fireplace can have surface temperatures that are too hot to touch. This level 

of surface temperature is considered normal and does not indicate any hazardous situation. 

 

Hearth Pad Temperatures 

New hearth protection pads installed are required to 

have a thermal insulation value of R-1. 
The top exposed surface of the noncombustible hearth 

pads can reach a temperature that is too hot to touch 

(as high as 250

o

F). This is considered normal. 

 

Surround Face Temperatures 

Areas of the breastplate directly above the top 

convection air gap of this Fireplace can be very hot (too 

hot to touch (exceeding 250

o

F)) and is deemed normal. 

 

Mantel Temperatures 

Mendota Fireplaces comply with ANSI Z21.88-2017 

standards for maximum surface temperatures on 

exposed “combustible” surfaces adjacent to the 

Fireplace.  Be aware that surface in front of, above and 

adjacent to this heater appliance can be too hot to 

touch. As long as all required clearances to 

combustibles are met and the required finishing 

materials are used, this appliance will perform safely. 

Note that the exposed surfaces immediately 

surrounding the Fireplace can have a surface temperature too hot to touch. This level of surface temperatures is considered 

normal and does not indicate any hazardous situation. 
WARNING: Surfaces surrounding this Fireplace can be very hot to the touch during operation. Carefully supervise children and 

pets while this Fireplace is operating. 

 

Figure 3-10 Hot Zones 

Содержание FV46

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды