Mendota FV46 Скачать руководство пользователя страница 21

Страница: 21 / 96

85-03-01108-C

FV46

Page

Convection Blower System

Dual blowers are provided as standard equipment with this FV46 Fireplace. The dual blowers have an air output rating of 190

CFM (in free air). This Fireplace is designed to operate with the blowers turned off or on. Turning the blower on aids in

distributing and circulating heat to the room this Fireplace is installed in.

Lifting Handles

Four lifting handles, one on each side and two on the rear wall, are provided. The lifting handles make it easy for two

individuals to lift and transport this Fireplace.

WARNING

: The lifting handles are designed only for lifting and moving the fireplace short distances. Such as lifting the

fireplace onto a transport cart or shifting the fireplace during installation. Do not attempt to carry this fireplace by the lifting

handles only.

Note: Team lifting is recommended.

To use the lifting handles, remove one screw that secures the upper section of the lifting handles and pull top section outward.

Slide hands into the opening of the lifting handle, grip top U-shaped section tightly and lift.

Figure 3-13 Lifting Handles

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды